quenching stress
英 [ˈkwentʃɪŋ stres]
美 [ˈkwentʃɪŋ stres]
网络 焼入応力; 骤冷应力
双语例句
- Experimental results showed that the service life of die can be improved evidently by using high temperature quenching and stress relief annealing.
实践证明，采用高温淬火和中间消应力退火可显著提高其使用寿命。 - However, stress re-distribution would occur in the non-uniform structural stress introduced by quenching with a low stress gradient.
而淬火引入非均匀的结构应力且梯度较小，主要发生应力重分布。 - Results show that both high temperature quenching and step quenching can apparently increase the stress corrosion cracking resistance K_ ( ISCC).
结果表明，高温淬火和分级淬火可使应力腐蚀断裂抚力K（ISCC）值得到明显提高。 - The study results are helpful to designing of quenching process and understanding of quenching stress and distortion regularity for complex thin shell.
研究结果有助于复杂薄壁壳体淬火工艺制订及淬火应力和畸变规律的认识。 - Marc by FEM. It analyses the distribution of quenching residual stress, achieves the law of the layered distribution of the residual stress along the radius according to temperature gradient.
Marc模拟无缝钢管淬火过程，分析了淬火残余应力的分布情况，得到了残余应力按照温度梯度沿半径方向分层分布的规律。 - In addition, the residual stresses of rolling, temperature rising-preservation-falling were simulated respectively, and the influence of rolling stress and temperature rising-preservation stress towards quenching stress were studied too.
文中顺次地仿真出轧制-升温-保温-急冷四个过程中产生的残余应力，研究轧制残余应力、升温-保温应力对最终淬火应力的影响。 - It is concluded that the local tensile stress created during quenching process and the stress concentration due to sharp V-shaped notch are the primary reasons of cracking.
认为，淬火过程中产生的局部拉应力加上尖锐V型槽口引起的应力集中是造成开裂的主要原因。 - Finite Element Calculation on Quenching Stress and Distortion of Carburized 20 Steel
20钢渗碳淬火应力与畸变的有限元计算 - The influence of rolling stress towards quenching stress is little, but quenching stress totally changes the original rolling stress.
轧制应力对淬火应力影响很小，淬火应力却彻底改变了原有轧制应力的大小和分布。 - The problem how to calculate the inactive PS ⅱ reaction centers with chlorophyll fluorescence kinetics under fluorescence quenching condition induced by high temperature stress was discussed.
本文讨论了在高温胁迫导致荧光猝灭的情况下如何用叶绿素荧光动力学计算PSⅡ无活性中心相对含量的问题。 - According to the FEM analyzing result, the influence of every initial strains to the quenching residual stress is attained.
根据有限元分析的结果，得到了淬火过程各项初应变对淬火残余应力的影响规律。 - INFLUENCE OF QUENCHING TEMPERATURE ON STRESS CORROSION IN 4330M STEEL& The Role of Impurity Segregation in Stress Corrosion Cracking of High Strength Steel
淬火温度对4330M钢应力腐蚀的影响&晶界上杂质偏聚对高强度钢应力腐蚀开裂的作用 - The quenching stress and distortion of carburized 20 steel are calculated by finite element.
对20钢渗碳后的淬火应力与畸变进行了有限元计算。 - Moreover, the effect of the latter welding subsection's quenching arc region on decreasing residual stress of the prior welding subsection is better than the striking arc region.
中间焊段的收弧区降低先焊焊段残余拉应力的效果要优于起弧区。 - Residual stress quenched are appearance between areas without plastic deformation and areas that Asymmetry plastic deformation quenching that thermal stress place a premium on.
淬火结束后，发生过不均匀塑性变形的区域和没有发生过塑性变形的区域之间的内应力就是淬火残余应力。 - Effect of the initial strains on the quenching residual stress during the quenching process
淬火过程初应变项对淬火残余应力的影响 - On condition that the sprocket ′ s hardness and effective hardening case depth meets the technical requirements, UCON A quenchant can minimize the PM sprocket ′ s induction quenching stress, and hence control the quenching crack rate within 1%.
在链轮硬度与有效硬化层深度达到技术要求的情况下，UCONA型水溶性淬火介质使铁基粉末冶金链轮感应淬火冷却时的应力降到最小，从而把淬火开裂比例控制在1%以内。 - The effect of quenching temperatures on the rate of stress corrosion crack propagation of4330M steel in distilled water has been investigated.
本文研究了淬火温度对4330M钢在蒸馏水中的应力腐蚀裂纹扩展速率的影响。 - Response of Chlorophyll Fluorescence Quenching Characteristics to Osmotic Stress on Leaves of Cotton in Northern Xinjiang
北疆棉花叶绿素荧光猝灭特性对渗透胁迫的响应 - The circumstance of service was simulated by water quenching and the thermal stress was analyzed.
利用水淬法模拟其服役状况并用有限差分方法对产生的非稳态热应力进行了分析。 - Computer Simulation of Quenching Stress Field during Gas Turbine Compressor Disk Quenching Process
重型燃机压气机盘淬火应力场的计算机模拟 - The hardening of the workpiece, s surface and the depth of the hardening layer can be ensured, and the deformities and the cracks due to quenching stress can be decreased by improving cooling equipments and increasing cooling intensity of oils.
通过改进冷却设施和提高油的冷却强度，既保证淬火时工件表面淬硬和淬透层深度，又尽量减少淬火应力所造成的变形或开裂。 - The study of the quenching remains stress function of the club-shaped metal
对金属棒形工件淬火残余应力函数的研究 - The induction quenching realizes imitated stress strengthening, raises fatigue limit and service performance of the torque rod.
感应淬火实现了仿应力强化，提高了扭杆的疲劳极限和使用性能。 - During the quenching, quenching stress and thermal stress jointly cause deformation of armor plate.
在淬火时，组织应力和热应力共同作用致使钢板变形。 - Then it require the cooling process control and deformation control of the spray quenching institutions. This article through the analysis and establishing quenching temperature field and stress field of the finite element model. And studied the influence of parameters on the uniform temperature quenching deformation.
本文通过分析并建立淬火冷却温度场和应力场有限元模型，研究了各参数对温度均匀性淬火变形的影响。 - Martensitic phase transformation ( MT) denotes a class of first-order, non-diffusive transformation in materials with high symmetry at high temperature ( called austenite) subjected to a quenching or applied stress.
马氏体相变是指一类由高温高对称性母相（奥氏体相）进行急剧降温或在应力作用下材料发生的一种非扩散型一级相变。